- Improving the mechanical properties and reducing the residual stresses of AA7075 by combination of cyclic close die forging and precipitation hardening
- Influence of Er addition on microstructure and mechanical properties of as-cast Mg-10Li-5Zn alloy
- High frequency model describing the noise transfer behaviour of automotive hydraulic engine mounts
- EXPONENTIAL STABILIZATION OF A TRANSVERSELY VIBRATING BEAM VIA BOUNDARY CONTROL
- Grain size effects on NiTi shape memory alloy fatigue crack growth
- Understanding the Enhancement Mechanisms of Surface Plasmon‐Mediated Photoelectrochemical Electrodes: A Case Study on Au Nanoparticle Decorated TiO 2 Nanotubes
- Effects of Damaged Boundaries on the Free Vibration of Kirchhoff Plates: Comparison of Perturbation and Spectral Collocation Solutions
- Measurement of the direct rebound effect of residential electricity consumption: An empirical study based on the China family panel studies
- Assessment of control tools for utilizing excess distributed photovoltaic generation in domestic electric water heating systems
- Design of a 2 MW ZrC/W-based molten-salt-to-sCO2 PCHE for concentrated solar power
- Renewable Energy Communities: Optimal sizing and distribution grid impact of photo-voltaics and battery storage
- Effect of Traverse and Rotational Speeds on the Tensile Behavior of the Underwater Dissimilar Friction Stir Welded Aluminum Alloys
- Mixed mode fracture behavior of short-particle engineered wood
- Joining of ceramic oxides by liquid wetting and capillarity
- Economic competitiveness of off-peak hydrogen production today – A European comparison
- Numerical investigation of effects on replenishment in rolling point contacts using CFD simulations
- Experimental Investigation of Centrifugal Effects on Lubricant Replenishment in the Starved Regime at High Speeds
- Lubricant Replenishment in Rolling Bearing Contacts
- Synthesis and characterization of organic-inorganic cross-linked membrane for the separation of mono-charged and double charged ions using UV irradiation
- Longitudinal wheel slip control using dynamic neural networks
- Fusion of driving and braking tire operational modes and analysis of traction dynamics and energy efficiency of a 4×4 loader
- Film Thickness and Rolling Resistance in Starved Elastohydrodynamic Lubrication of Point Contacts With Reflow
- Machine learning and simulation-based surrogate modeling for improved process chain operation
- Numerical Modeling of Radiated Sound for Impact Pile Driving in Offshore Environments
- Algorithmic formulation of clay and sand pipe–soil interaction models for on-bottom stability analysis
- Design and analysis of novel 2R1T generalized parallel mechanisms with large rotational angles
- Preparation and characterization of Fe3O4/polystyrene composite particles via inverse emulsion polymerization
- Nonlinear dynamics of piezoelectric-based active nonlinear vibration absorber using time delay acceleration feedback
- Two-dimensional theory of piezoelectric shells considering surface effect
- Durability of Mat Glazes in Hydrochloric Acid Solution
- The role of damping, mass and stiffness in the reduction of wind effects on structures
- A decentralized cooperative framework for multi-area active distribution network in presence of inter-area soft open points
- Modal Overlap Factor of a beam with an acoustic black hole termination
- Prediction of deformation behavior of glassy polymers based on molecular chain network model
- Distribution characteristics of falling film thickness around a horizontal corrugated tube
- Theoretical analysis of harbor resonance in harbor with an exponential bottom profile
- Chemical bath deposition of SnS:Cu/ZnS for solar hydrogen production and solar cells
- Rate dependent fracture along a silicon/epoxy interface under mixed-mode loading conditions
- Improvement of the SST γ-Reθt transition model for flows along a curved hydrofoil
- Analysis and Comparison of the Performance of an Inverted Brayton Cycle and Turbocompounding With Decoupled Turbine and Continuous Variable Transmission Driven Compressor for Small Automotive Engines
- Perseverance of direct bandgap in multilayer 2D PbI 2 under an experimental strain up to 7.69%
- Synthesis of Sn nanowire by template electrodeposition and its conversion into Sn nanosolder
- Ultra-broadband piezoelectric energy harvesting via bistable multi-hardening and multi-softening
- An improved quasi-zero stiffness vibration isolation system utilizing dry friction damping
- Dynamics of Bed for Regeneration of Cerium Oxide High-Temperature Coal Gas Desulfurization Sorbent
- A comprehensive review on the application of nanofluids in the machining process
- Active nonlinear energy sink using force feedback under transient regime
- Linearization approaches for general multibody systems validated through stability analysis of a benchmark bicycle model
- Multi-objective frequency domain-constrained static output feedback control for delayed active suspension systems with wheelbase preview information
- Ageing of autoclaved epoxy/flax composites: Effects on water absorption, porosity and flexural behaviour
[ صفحه 1 از 3117 ]
بعدی